Subaru Legacy

Since 1990-1998 of release

Repair and car operation



Subaru Legasi
+ 1.1. Identification numbers
+ 2. Maintenance service
+ 3. Engines
+ 4. Heating, ventilation
+ 5. Fuel system
+ 6. An exhaust system
+ 7. Systems of start, ignition
+ 8. Transmissions
- 9. Coupling, shaft
   9.1. Technical characteristics
   + 9.2. Coupling
   + 9.3. A kardannyj shaft
   - 9.4. Power shafts
      9.4.1. A forward power shaft
      9.4.2. A back power shaft (models 4WD)
      - 9.4.3. Replacement of protective covers of hinges of equal angular speeds
         9.4.3.1. The hinge with balls and a separator
         9.4.3.2. The trehplechy hinge with rollers
      9.4.4. The external hinge of a power shaft
      9.4.5. Replacement of sealing rings of back differential
      9.4.6. Back main transfer
+ 10. Brake system
+ 11. A suspension bracket
+ 12. A steering
+ 13. A body
+ 14. An electric equipment


e2a7ff6d e2a7ff6d

9.4.3. Replacement of protective covers of hinges of equal angular speeds

9.4.3.1. The hinge with balls and a separator
THE GENERAL DATA

Power shaft with the hinge with balls and a separator

1 – a spring pin
2 – a ring
3 – the hinge case (all forward power shafts and back приводные
Shaft with 1990 for 1994)
4 – a lock ring
5 – an internal ring
6 – balls
7 – a separator
8 – a fixing ring
9 – a collar
10 – a protective cover
11 – a protective cover
12 – the external hinge of a power shaft
13 – a ring (only forward power shafts)
14 – the case of the external hinge (only back power shafts since 1995)

Dismantling

PERFORMANCE ORDER
1. Remove a power shaft.
2. Fix a power shaft in a vice with soft sponges.
3. Remove collars of fastening of a protective cover.
4. Remove a protective cover from the case of the internal hinge.
5. Take fixing ring from the case of the internal hinge.
6. Remove the case of the internal hinge from a power shaft.
7. Clean old greasing from the hinge of equal angular speeds.
8. Remove a lock ring from the power shaft end.
9. Remove an internal ring with balls from a power shaft.
10. Using a paint, note mutual position of an internal ring and a separator.
11. Using a screw-driver edge, take balls from a separator.
12. Turn an internal ring on 90 , thus combine ledges of an internal ring with separator windows.
13. Take an internal ring from a separator.

Check

PERFORMANCE ORDER
1. Using solvent, clear all details of the hinge.
2. Check up a condition of details on presence of dot corrosion, scratches, cracks and damages (on the right – an internal ring of the hinge, at the left – a separator).
3. In the presence of defects replace the hinge in gathering.

Assemblage

PERFORMANCE ORDER
1. Establish an internal ring in a separator, thus combine adjusting labels.
2. Insert balls into separator windows.
3. Not to damage a protective cover at installation on a power shaft, wind with a sticky tape шлицы a power shaft.
4. Pull over a power shaft a small collar of fastening of a protective cover, and then a protective cover and remove a sticky tape.
5. Establish assemblage of an internal ring of a separator and balls on a power shaft.
6. Establish a lock ring.
7. Fill with fresh greasing the hinge of equal angular speeds.
8. Establish the case of the internal hinge on a power shaft and fix its fixing ring.
9. Remove surpluses of greasing and establish a protective cover on the case of the hinge of equal angular speeds.
10. Then let the air out from under a protective cover.
11. Using the special tool, fix a protective cover new collars.
12. Fix the lock of a collar of a protective cover.
13. Cut off an acting tail of a collar.
14. Establish a protective ring on the big collar of fastening of a protective cover.
15. Establish a power shaft.