Subaru Legacy

Since 1990-1998 of release

Repair and car operation



Subaru Legasi
+ 1.1. Identification numbers
+ 2. Maintenance service
+ 3. Engines
+ 4. Heating, ventilation
+ 5. Fuel system
+ 6. An exhaust system
+ 7. Systems of start, ignition
- 8. Transmissions
   + 8.1. A mechanical transmission
   - 8.2. An automatic transmission
      8.2.1. Introduction
      8.2.2. Technical characteristics
      8.2.3. Diagnostics of leak of operational liquids
      8.2.4. The lever and a gear change cable
      8.2.5. A cable of a choice of transfers
      8.2.6. The switch of blocking of a starter and backing light
      8.2.7. Replacement of sealing rings
      8.2.8. Check and replacement of support of a transmission
      8.2.9. Adjustment of a brake tape
      8.2.10. Removal and transmission installation
+ 9. Coupling, shaft
+ 10. Brake system
+ 11. A suspension bracket
+ 12. A steering
+ 13. A body
+ 14. An electric equipment


e2a7ff6d e2a7ff6d

8.2.4. The lever and a gear change cable
THE GENERAL DATA

The lever of a gear change of cars with 1990 for 1994

1 – a cover
2 – the switch button
3 – the handle button
4 – a spring
5 – the handle
6 – the indicator of the included transfer
7 – the starting position switch
8 – a control lamp
9 – the unblocking button
10 – the basis of the lever of a gear change
11 – the solenoid
12 – a lining
13 – a cover of a cable of a choice of transfers
14 – a nut
15 – a cable of a choice of transfers
16 – a nut
17 – draught,
18 – a lock plate
19 – the gear change lever
20 – a washer
21 – a lining
22 – a lining
23 – a cover
24 – a pin
25 – a pin

The lever of a gear change of models since 1995

1 – the button
2 – a spring
3 – the handle
4 – the indicator of the included transfer
5 – the starting position switch
6 – a control lamp
7 – the solenoid of the lock of displacement
8 – the basis of the lever of a gear change
9 – a lining
10 – a cable cover
11 – a nut
12 – a nut
13 – a cable
14 – скоба
15 – draught
16 – the gear change lever
17 – a lock plate
18 – a spring
19 – a pin
20 – a lining
21 – a washer
22 – a cover
23 – a lining
24 – a pin

Removal

PERFORMANCE ORDER
1. Establish the gear change lever in neutral position.
2. Lift the car and fix on supports.
3. Remove a reception exhaust pipe.
4. Disconnect a cable of a choice of transfers from the lever on a transmission (bolts of fastening of a cover of a cable are specified by arrows).
5. Unscrew the tyre of grounding from картера transmissions.
6. Disconnect a cable of a choice of transfers from the gear change lever. For a detachment of a cable of a choice of transfers from the gear change lever unscrew a nut on the cable end (the left arrow) then unscrew a nut of fastening of a cover of a cable (the right arrow) and take a cable from a groove.
7. Unscrew a nut of fastening of a cover of a cable of a choice of transfers and take a cable through a groove in an arm.
8. Remove the central console.
9. Unscrew two screws of fastening of the handle of the lever of a gear change and, having pulled the handle upwards, remove it from the gear change lever.
10. Disconnect electric sockets from the solenoid of the lock of displacement and the starting position switch.
11. Unscrew 4 screws (are specified by arrows) fastenings of the indicator of position of the included transfer.
12. Raise the indicator and disconnect an electric socket of lamps накаливания.
13. Unscrew screws of fastening of the basis of the lever of a gear change (are specified by arrows) and take assemblage of the lever of a gear change from the car.
14. Installation is made in sequence, return to removal. Adjust a cable of a choice of transfers.