Subaru Legacy

Since 1990-1998 of release

Repair and car operation



Subaru Legasi
+ 1.1. Identification numbers
+ 2. Maintenance service
+ 3. Engines
+ 4. Heating, ventilation
+ 5. Fuel system
+ 6. An exhaust system
+ 7. Systems of start, ignition
- 8. Transmissions
   + 8.1. A mechanical transmission
   - 8.2. An automatic transmission
      8.2.1. Introduction
      8.2.2. Technical characteristics
      8.2.3. Diagnostics of leak of operational liquids
      8.2.4. The lever and a gear change cable
      8.2.5. A cable of a choice of transfers
      8.2.6. The switch of blocking of a starter and backing light
      8.2.7. Replacement of sealing rings
      8.2.8. Check and replacement of support of a transmission
      8.2.9. Adjustment of a brake tape
      8.2.10. Removal and transmission installation
+ 9. Coupling, shaft
+ 10. Brake system
+ 11. A suspension bracket
+ 12. A steering
+ 13. A body
+ 14. An electric equipment


8.2.10. Removal and transmission installation

Removal

PERFORMANCE ORDER
1. Open a cowl and fix it in this position.
2. Remove a wire of weight from the accumulator.
3. Remove an air inlet tubule.
4. Mark and disconnect electric sockets from the forward gauge of oxygen, a plait of a transmission, grounding of a transmission, the switch of blocking of a starter and lanterns of a backing and the gauge of speed of the car.
5. Remove a starter.
6. Remove a forward support of the engine (bolts of fastening of a support are specified by arrows).
7. Instead of an engine support it is recommended to establish the special tool to adjust an angle of slope of the engine for simplification of removal of a transmission. In the absence of the special tool it is necessary to use a jack to lift a forward part of the engine.
8. Unscrew the hydrotransformer from a drive plate.
9. Remove a stopper (it is specified by an arrow) from a mechanism aperture газораспределения.
10. Note mutual position of the hydrotransformer and a drive plate (the arrow specifies an arrangement of a bolt of fastening of the hydrotransformer to a drive plate).
11. Unscrew 4 bolts, which крепят the hydrotransformer to a drive plate.
12. Take щуп for measurement of level of oil.
13. Unscrew the top right bolt (it is specified by an arrow) transmission fastenings to the engine.
14. Lift the car and fix on supports.
15. Disconnect an electric socket from the back gauge of oxygen.
16. Remove a forward part of an exhaust system.
17. Merge oil from a transmission.
18. Disconnect hoses of the heat exchanger from metal pipes on a transmission.
19. Unscrew the top arm of fastening of a pipe for щупа measurements of level of oil.
20. Unscrew the bottom bolt of fastening of a pipe for щупа measurements of level of oil.
21. On models 4WD remove карданный a shaft.
22. Disconnect a cable of a choice of transfers from the lever on a transmission and remove a cover of a cable from a transmission.
23. Unscrew a clip of the plug of the stabilizer of cross-section stability from a beam.
24. Disconnect power shafts from a transmission.
25. Unscrew the bottom nuts (are specified by arrows) transmission fastenings to the engine.
26. Prop up a transmission a jack.
27. Remove a back beam, having unscrewed bolts and fastening nuts (are specified by arrows).
28. Using the special adaptation established instead of a forward support of the engine, or using a jack, raise a forward part of the engine.
29. Moving a transmission from the engine, disconnect the hydrotransformer from a plate of a drive and lower a transmission downwards. Keep the hydrotransformer on primary to a transmission shaft.

Installation

PERFORMANCE ORDER
1. Lift a transmission and combine with the engine.
2. Establish a back beam.
3. Slowly move a transmission to the engine and screw the bottom nuts of fastening of a transmission, having tightened their demanded moment. Screw in the top bolt of fastening of a transmission to the engine and tighten its demanded moment.
4. Combine labels on the hydrotransformer and a plate of a drive and fix the hydrotransformer to a plate of a drive bolts, having tightened their demanded moment.
5. Establish power shafts.
6. Screw clips of the plug of the stabilizer of cross-section stability.
7. Connect a cable of a choice of transfers to the lever of a choice of transfers of a transmission and check up its adjustment.
8. On models 4WD establish карданный a shaft.
9. Connect hoses of the heat exchanger and establish a pipe for щупа for measurement of level of oil.
10. Establish earlier removed elements of an exhaust system.
11. Connect an electric socket of the back gauge of oxygen.
12. Lower the car.
13. Establish a forward support of the engine.
14. Establish a starter.
15. Connect electric sockets of the forward gauge of oxygen, a plait of a transmission, the tyre of grounding, the switch of blocking of a starter and light of a backing and the gauge of speed of the car.
16. Add a recommended liquid in a transmission and establish щуп for measurement of level of a liquid.
17. Connect a weight wire to the accumulator.
18. Check up work of a cable of a choice of transfers.