Subaru Legacy

Since 1990-1998 of release

Repair and car operation



Subaru Legasi
+ 1.1. Identification numbers
+ 2. Maintenance service
+ 3. Engines
+ 4. Heating, ventilation
+ 5. Fuel system
+ 6. An exhaust system
+ 7. Systems of start, ignition
- 8. Transmissions
   - 8.1. A mechanical transmission
      8.1.1. Introduction
      8.1.2. Technical characteristics
      8.1.3. The gear change lever
      8.1.4. Check and replacement of support of a transmission
      8.1.5. Switches of light of a backing and neutral position КП
      8.1.6. Removal and transmission installation
   + 8.2. An automatic transmission
+ 9. Coupling, shaft
+ 10. Brake system
+ 11. A suspension bracket
+ 12. A steering
+ 13. A body
+ 14. An electric equipment


e2a7ff6d фильтр сетчатый фланцевый gross
данфосс гибкие вставки
Нототения источник.
e2a7ff6d фильтр сетчатый фланцевый gross
данфосс гибкие вставки
Нототения источник.

8.1.6. Removal and transmission installation

Removal

PERFORMANCE ORDER
1. Open a cowl and fix it in open position.
2. Remove a wire of weight from the accumulator.
3. If on the car it is established тросовый a coupling drive, disconnect a coupling cable. If on the car the hydraulic drive of coupling is established, separate the working cylinder of coupling from a transmission.

The prevention

Do not press a pedal of coupling after removal of the working cylinder of coupling from a transmission.


4. Remove a forward support (fig. of the Detail of the lever of a gear change of models 4WD see). Instead of a forward support it is recommended to establish the special tool for adjustment of an angle of slope of the engine for simplification of removal of a transmission. In the absence of the special tool it is necessary to use a jack slightly to raise a forward part of the engine
5. Mark and disconnect electric sockets from a transmission.
6. Remove a starter.
7. Unscrew the top right bolt of fastening of a transmission to the engine.
8. Lift the car and fix on supports. Merge oil from a transmission.
9. Remove the elements of an exhaust system interfering removal of a transmission.
10. Unscrew the tyre of grounding of a transmission.
11. Disconnect a cable of a drive of a speedometer on the right side of a transmission.
12. On models 4WD remove карданный a shaft.
13. Disconnect from a transmission draught of the shock-absorber, a spring and draught of a gear change.
14. Disconnect hinges of power shafts from a transmission.
15. Prop up a transmission a jack.
16. Unscrew and remove forward, central and back beams.
17. Unscrew two bottom nuts of fastening of a transmission to the engine.
18. Using the special tool established instead of a forward support or using a jack, raise a forward part of the engine so that the back part of the engine was at an angle downwards. Move a transmission from the engine to take an entrance shaft of a transmission from a nave of a disk of coupling, and slowly lower a transmission.

Installation

PERFORMANCE ORDER
1. Apply a thin film universal greasing on grooves of an entrance shaft of a transmission. Raise a transmission and combine it with the engine.
2. Slowly moving a transmission to the engine, insert an entrance shaft of a transmission into a nave of a disk of coupling. Screw the bottom nuts of fastening of a transmission on the engine.
3. Establish back, central and forward beams and fix bolts and nuts.
4. Remove a jack supporting a transmission.
5. Attach to a transmission power shafts.
6. Establish on a transmission draught of the shock-absorber and draught of a gear change.
7. On models 4WD establish карданный a shaft.
8. Establish the elements of an exhaust system removed earlier.
9. Connect electric sockets of the gauge of oxygen, the switch of light of a backing and the switch of neutral position of a transmission.
10. Connect a cable of a drive of a speedometer.
11. Lower the car.
12. Establish the top bolt of fastening to the engine and tighten its demanded moment.
13. Establish a starter.
14. Remove the special tool and establish a forward support.
15. Connect to a transmission the grounding tyre.
16. Establish a cable of coupling and adjust a free wheeling of a cable or establish the working cylinder of coupling on a transmission.
17. Connect to the accumulator a weight wire.
18. Fill in oil in a transmission.