Subaru Legacy

Since 1990-1998 of release

Repair and car operation


Subaru Legasi
+ 1.1. Identification numbers
+ 2. Maintenance service
+ 3. Engines
+ 4. Heating, ventilation
- 5. Fuel system
   5.1. Introduction
   5.2. Technical characteristics
   5.3. Pressure removal in fuel system
   5.4. Check of the fuel pump
   5.5. The fuel pump
   5.6. A fuel separator (only models 4WD)
   5.7. The gauge of level of fuel
   5.8. A fuel tank
   5.9. A casing of the air filter
   5.10. An accelerator cable
   5.11. Electronic system of injection of fuel
   5.12. Fuel system
   5.13. System of giving of air
   5.14. Electronic control system
   5.15. Check of system of injection of fuel
   + 5.16. Check and replacement of elements of system of injection of fuel
   5.17. Турбонагнетатель
   5.18. Check of the executive mechanism заслонки турбонагнетателя
   5.19. The general check турбонагнетателя
   5.20. Removal and installation турбонагнетателя
+ 6. An exhaust system
+ 7. Systems of start, ignition
+ 8. Transmissions
+ 9. Coupling, shaft
+ 10. Brake system
+ 11. A suspension bracket
+ 12. A steering
+ 13. A body
+ 14. An electric equipment


e2a7ff6d проститутки проститутки питера проститутки дешево досуг.
строительство бани своими руками.
На http://zz-yalta.ru жилые комплексы и новостройки ялты: цены.
Билеты на самолет в нижнем новгороде, favka ооо.
e2a7ff6d проститутки проститутки питера проститутки дешево досуг.
строительство бани своими руками.
На http://zz-yalta.ru жилые комплексы и новостройки ялты: цены.
Билеты на самолет в нижнем новгороде, favka ооо.

5.20. Removal and installation турбонагнетателя Removal

PERFORMANCE ORDER
1. Remove a wire of weight from the accumulator.
2. Merge cooling liquid from cooling system.
3. Remove a casing of a collector and disconnect system of ventilation of a crater from system of an admission of air.
4. Disconnect an air inlet tube, assemblage of the air filter and the resonator and remove them from the top part of the engine (fig. the Air filter of the engine with турбонагнетателем see).
5. Disconnect a hose of giving of a cooling liquid to турбонагнетателю (Detail fig. турбонагнетателя see).
6. Remove an arm турбонагнетателя.
7. Remove an entrance tube турбонагнетателя.
8. Unscrew bolts and remove tubes of giving and return of oil from турбонагнетателя.
9. Unscrew nuts, крепящие турбонагнетатель to a final collector and, being careful, remove турбонагнетатель.
10. The bottom bolts of fastening картера couplings to the block of cylinders.

Installation

PERFORMANCE ORDER
1. Establish турбонагнетатель on a final collector together with a new lining and fix bolts.
2. Connect the pipeline of return of oil to турбонагнетателю.
3. Through an aperture for connection of the pipeline of giving of oil to турбонагнетателю fill in pure oil in турбонагнетатель and turn the turbine турбонагнетателя. Screw the pipeline of giving of oil to турбонагнетателю.
4. The further installation is made in sequence, return to removal.