Subaru Legacy

Since 1990-1998 of release

Repair and car operation



Subaru Legasi
+ 1.1. Identification numbers
+ 2. Maintenance service
+ 3. Engines
- 4. Heating, ventilation
   + 4.1. Cooling system
   - 4.2. Heating system
      4.2.1. The heater fan
      4.2.2. A heater radiator
      4.2.3. The control panel a heater
   + 4.3. Air central air
   4.4. Climate control system
+ 5. Fuel system
+ 6. An exhaust system
+ 7. Systems of start, ignition
+ 8. Transmissions
+ 9. Coupling, shaft
+ 10. Brake system
+ 11. A suspension bracket
+ 12. A steering
+ 13. A body
+ 14. An electric equipment


e2a7ff6d бадминтон купить
Электрический станок для заточки ножей на сайте zatochka-sharp.ru.
Купить Асик miner на www.miningmoon.ru.
монтаж станка - Сбор.
e2a7ff6d бадминтон купить
Электрический станок для заточки ножей на сайте zatochka-sharp.ru.
Купить Асик miner на www.miningmoon.ru.
монтаж станка - Сбор.

4.2.3. The control panel a heater
THE GENERAL DATA

The control panel a heater of models with 1990 for 1994


The control panel a heater of models since 1995


Check of the switch of the distributor of a stream of air on models with 1990 till 1994


Check of the switch of the distributor of a stream of air on models since 1995



Details of adjustment of position VENT


Check of the distributor of air in position FRESH


Details of a control lever in temperature of air


Engine check заслонки


Engine check заслонки arriving air

Check

PERFORMANCE ORDER
1. Start the engine and warm up it to normal working temperature.
2. Switching the fan switch, the distributor of a stream of air and moving the handle of adjustment of temperature, check up working capacity of system of heating (fig. the Control panel a heater of models with 1990 for 1994, fig. the Control panel a heater of models since 1995 see).
Air distributor
3. Remove the panel of devices. Using a tester connected to a socket of the block of management, check up working capacity of the switch (Check of the switch of the distributor of a stream of air fig. see models with 1990 till 1994, Check of the switch of the distributor of a stream of air fig. see models since 1995).
Adjustment of giving of air
4. First of all it is necessary to adjust system of ventilation of salon. Connect an electric socket заслонки distributions of air and turn a key in the ignition lock in position АСС. Press the button "air distribution" VENT. Thus lateral draught moves to the holder of draught.
5. Press button DEF and check up that lateral draught moves within a full range of a course (fig. of the Detail of adjustment of position VENT see).  
6. Then check up adjustment of giving of fresh air. Press the button of switch FRESH AIR and connect a plait to the engine operating giving of fresh air. Turn a key in the ignition lock in position АСС, press the button of switch RECIRC and check up that заслонка has moved to position рециркуляции air (fig. Check of the distributor of air in position FRESH see).
The lever of adjustment of temperature of air
7. Connect a cable of adjustment of temperature and establish the lever of adjustment of temperature in full cold position (fig. of the Detail of a control lever in temperature of air see).
8. Fix a cover of a cable of adjustment of temperature a clip and check up, that the cable cover did not move at moving of the lever of adjustment of temperature.
The engine заслонки
9. Using additional wires, submit pressure of the accumulator to contacts 1 and 2 electric sockets of the engine заслонки. Thus observe of engine rotation заслонки (fig. engine Check заслонки see).
If at check the engine заслонки does not work, replace the engine.
Engine check заслонки arriving air
10. On models with an electric motor заслонки arriving air check up action заслонки, submitting additional wires pressure of the accumulator to an electric socket (fig. engine Check заслонки arriving air see).
11. If at check the engine заслонки arriving air, replace the engine.

Removal

Arrangement of screws of fastening of the control panel a heater on models with 1990 till 1994

Screws are specified by arrows.

Arrangement of screws of fastening of the control panel a heater on models since 1995

Screws are specified by arrows.

Detachment of an electric socket of the switch of the fan

 

The prevention

On some models the safety air cushion is established. Therefore it is necessary to remove a wire of weight from the accumulator and to wait at least one minute before work about the gauge of collision or the panel of devices to avoid casual expansion of an air cushion of safety.


PERFORMANCE ORDER
1. Remove a wire of weight from the accumulator.
2. Remove furnish of the central part of the panel of devices.
3. Unscrew screws and take the control panel a heater from the panel of devices (the Arrangement of screws of fastening of the control panel a heater fig. see models with 1990 till 1994, fig. the Arrangement of screws of fastening of the control panel a heater on models since 1995).
4. Disconnect a cable of adjustment of temperature from the control panel.
5. Disconnect an electric socket of a plait of wires of the switch of the fan and take the control panel a heater from the car (fig. the Detachment of an electric socket of the switch of the fan see).

Installation

PERFORMANCE ORDER
Installation is made in sequence, return to removal. Adjust a cable of adjustment of temperature.