Subaru Legacy

Since 1990-1998 of release

Repair and car operation



Subaru Legasi
+ 1.1. Identification numbers
+ 2. Maintenance service
- 3. Engines
   3.1. Technical characteristics
   3.2. Operations on repair of the engine established in the car
   3.3. The top dead point of the first cylinder
   3.4. A cover of a head of the block of cylinders
   3.5. An inlet collector
   + 3.6. A gear belt and pulleys
   3.7. Replacement of a forward sealing ring of a cranked shaft
   3.8. Replacement of sealing rings of camshafts
   3.9. Camshafts and pushers
   3.10. Heads of the block of cylinders
   3.11. The oil pallet
   3.12. The oil pump
   3.13. The Flywheel / a drive plate
   3.14. Replacement of a back sealing ring of a cranked shaft
   3.15. A suspension bracket of the power unit
   - 3.16. Engine major repairs
      3.16.1. Technical characteristics
      3.16.2. Compression check
      3.16.3. Check of the engine by means of the vacuum gauge
      3.16.4. Recommendations about engine removal
      3.16.5. Engine removal
      3.16.6. Sequence of dismantling of the engine
      3.16.7. Dismantling of a head of the block of cylinders
      3.16.8. Clearing and survey of a head of the block of cylinders
      3.16.9. Assemblage of a head of the block of cylinders
      3.16.10. Removal of pistons
      3.16.11. Division of sections of blocks of cylinders
      3.16.12. Removal of a cranked shaft from rods
      3.16.13. The block of cylinders of the engine
      3.16.14. Хонингование cylinders
      3.16.15. Rods
      3.16.16. A cranked shaft
      3.16.17. Survey radical and шатунных bearings
      3.16.18. Engine balance of assembly at major repairs
      3.16.19. Survey of pistons
      3.16.20. Check of working backlashes шатунных bearings
      3.16.21. Check of working backlashes of radical bearings of a cranked shaft
      3.16.22. Assemblage of sections of the block of cylinders
      3.16.23. Installation of piston rings
      3.16.24. Installation of pistons
      3.16.25. Engine installation
      3.16.26. Start of the engine after major repairs
+ 4. Heating, ventilation
+ 5. Fuel system
+ 6. An exhaust system
+ 7. Systems of start, ignition
+ 8. Transmissions
+ 9. Coupling, shaft
+ 10. Brake system
+ 11. A suspension bracket
+ 12. A steering
+ 13. A body
+ 14. An electric equipment


e2a7ff6d e2a7ff6d

3.16.6. Sequence of dismantling of the engine
THE GENERAL DATA

The basic details and engine knots

1 – the gauge of pressure of oil
2 – the right block of cylinders
3 – заглушка
4 – a lining
5 – an oil separator cover
6 – a bypass pipe of system
Coolings
7 – the oil pump
8 – a forward sealing ring
9 – a back sealing ring
10 – a sealing ring of round section
11 – a flange
12 – the left block of cylinders
13 – the water pump
14 – a partition
15 – an arm of the mesh filter
16 – the mesh filter
17 – a lining
18 – the oil pallet
19 – a stopper oil plum
20 – a lining
21 – directing for щупа measurements of level of oil

If full major repairs of the engine are planned, disassemble the engine on making details in a following order:

  – External knots of the engine;
  – A flywheel / a drive plate;
  – A gear belt and pulleys;
  – The oil pallet;
  – A pipe маслоприемника with the mesh filter;
  – The oil pump;
  – Covers of a head of the block of cylinders;
  – Assemblage коромысел (the engine 2,2);
  – Camshafts;
  – Heads of the block of cylinders;
  – Pistons;
  – картер;
  – A cranked shaft and rods.