Subaru Legacy

Since 1990-1998 of release

Repair and car operation



Subaru Legasi
+ 1.1. Identification numbers
+ 2. Maintenance service
- 3. Engines
   3.1. Technical characteristics
   3.2. Operations on repair of the engine established in the car
   3.3. The top dead point of the first cylinder
   3.4. A cover of a head of the block of cylinders
   3.5. An inlet collector
   + 3.6. A gear belt and pulleys
   3.7. Replacement of a forward sealing ring of a cranked shaft
   3.8. Replacement of sealing rings of camshafts
   3.9. Camshafts and pushers
   3.10. Heads of the block of cylinders
   3.11. The oil pallet
   3.12. The oil pump
   3.13. The Flywheel / a drive plate
   3.14. Replacement of a back sealing ring of a cranked shaft
   3.15. A suspension bracket of the power unit
   - 3.16. Engine major repairs
      3.16.1. Technical characteristics
      3.16.2. Compression check
      3.16.3. Check of the engine by means of the vacuum gauge
      3.16.4. Recommendations about engine removal
      3.16.5. Engine removal
      3.16.6. Sequence of dismantling of the engine
      3.16.7. Dismantling of a head of the block of cylinders
      3.16.8. Clearing and survey of a head of the block of cylinders
      3.16.9. Assemblage of a head of the block of cylinders
      3.16.10. Removal of pistons
      3.16.11. Division of sections of blocks of cylinders
      3.16.12. Removal of a cranked shaft from rods
      3.16.13. The block of cylinders of the engine
      3.16.14. Хонингование cylinders
      3.16.15. Rods
      3.16.16. A cranked shaft
      3.16.17. Survey radical and шатунных bearings
      3.16.18. Engine balance of assembly at major repairs
      3.16.19. Survey of pistons
      3.16.20. Check of working backlashes шатунных bearings
      3.16.21. Check of working backlashes of radical bearings of a cranked shaft
      3.16.22. Assemblage of sections of the block of cylinders
      3.16.23. Installation of piston rings
      3.16.24. Installation of pistons
      3.16.25. Engine installation
      3.16.26. Start of the engine after major repairs
+ 4. Heating, ventilation
+ 5. Fuel system
+ 6. An exhaust system
+ 7. Systems of start, ignition
+ 8. Transmissions
+ 9. Coupling, shaft
+ 10. Brake system
+ 11. A suspension bracket
+ 12. A steering
+ 13. A body
+ 14. An electric equipment


3.16.5. Engine removal
THE GENERAL DATA

Fastening a sling of the load-lifting mechanism on a back part of the engine


Fastening a sling of the load-lifting mechanism on a forward part of the engine


PERFORMANCE ORDER
1. Remove a cowl.
2. Remove mudguards from the bottom part of the engine.
3. Remove pressure in fuel system.
4. Disconnect from the accumulator of the plug and remove the accumulator.
5. Merge cooling liquid from system of cooling of the engine. Then remove the bottom hose of a radiator.
6. Disconnect electric sockets from the radiator fan.
7. Disconnect hoses and electric sockets from the air filter and remove assemblage of the air filter.
8. Remove the radiator fan, a radiator, radiator hoses.
9. Remove the air conditioning compressor.
10. Remove the generator and a starter.
11. Unscrew the tyre of grounding from the left head of the block of cylinders.
12. Remove high-voltage wires from spark plugs.
13. Remove an inlet collector.
14. Disconnect heater hoses.
15. Remove an arm of high-voltage wires from a forward part of the engine.
16. If the car is equipped by the steering amplifier unscrew bolts of fastening of the pump of the amplifier of a steering and move it aside, without disconnecting hoses.
17. Lift a forward part of the car and fix on supports.
18. Disconnect an electric socket from the oxygen gauge, then separate a forward reception exhaust pipe from heads of the block of cylinders.
19. If the car is equipped by an automatic transmission, look subsection 8.2.10 for removal of the hydrotransformer from a drive plate.
20. Unscrew two top bolts and ослабьте two bottom nuts of fastening of a transmission to the engine.
21. Unscrew nuts of fastening of forward support of the engine.
22. Hook on the engine the load-lifting mechanism, and a transmission prop up a jack (Fastening a sling of the load-lifting mechanism fig. see a back part of the engine, Fastening a sling of the load-lifting mechanism on a forward part
The engine
).
23. Raise the engine the load-lifting mechanism so that the engine top was perceived by the load-lifting mechanism.
24. Unscrew two bottom nuts of fastening of a transmission to the engine. Check up that anything else does not connect the engine to a car body.
25. Slowly lift the power unit from a motor compartment.
26. Move the engine aside from the car and lower on wooden supports on a floor or remove a flywheel / a plate of a drive and establish the engine on a special bed.