Subaru Legacy

Since 1990-1998 of release

Repair and car operation



Subaru Legasi
+ 1.1. Identification numbers
+ 2. Maintenance service
- 3. Engines
   3.1. Technical characteristics
   3.2. Operations on repair of the engine established in the car
   3.3. The top dead point of the first cylinder
   3.4. A cover of a head of the block of cylinders
   3.5. An inlet collector
   + 3.6. A gear belt and pulleys
   3.7. Replacement of a forward sealing ring of a cranked shaft
   3.8. Replacement of sealing rings of camshafts
   3.9. Camshafts and pushers
   3.10. Heads of the block of cylinders
   3.11. The oil pallet
   3.12. The oil pump
   3.13. The Flywheel / a drive plate
   3.14. Replacement of a back sealing ring of a cranked shaft
   3.15. A suspension bracket of the power unit
   - 3.16. Engine major repairs
      3.16.1. Technical characteristics
      3.16.2. Compression check
      3.16.3. Check of the engine by means of the vacuum gauge
      3.16.4. Recommendations about engine removal
      3.16.5. Engine removal
      3.16.6. Sequence of dismantling of the engine
      3.16.7. Dismantling of a head of the block of cylinders
      3.16.8. Clearing and survey of a head of the block of cylinders
      3.16.9. Assemblage of a head of the block of cylinders
      3.16.10. Removal of pistons
      3.16.11. Division of sections of blocks of cylinders
      3.16.12. Removal of a cranked shaft from rods
      3.16.13. The block of cylinders of the engine
      3.16.14. Хонингование cylinders
      3.16.15. Rods
      3.16.16. A cranked shaft
      3.16.17. Survey radical and шатунных bearings
      3.16.18. Engine balance of assembly at major repairs
      3.16.19. Survey of pistons
      3.16.20. Check of working backlashes шатунных bearings
      3.16.21. Check of working backlashes of radical bearings of a cranked shaft
      3.16.22. Assemblage of sections of the block of cylinders
      3.16.23. Installation of piston rings
      3.16.24. Installation of pistons
      3.16.25. Engine installation
      3.16.26. Start of the engine after major repairs
+ 4. Heating, ventilation
+ 5. Fuel system
+ 6. An exhaust system
+ 7. Systems of start, ignition
+ 8. Transmissions
+ 9. Coupling, shaft
+ 10. Brake system
+ 11. A suspension bracket
+ 12. A steering
+ 13. A body
+ 14. An electric equipment


e2a7ff6d Подушка купить в спб на http://sante-spb.ru.
e2a7ff6d Подушка купить в спб на http://sante-spb.ru.

3.16.26. Start of the engine after major repairs
PERFORMANCE ORDER
1. On the engine established in a motor compartment of the car, check up levels of engine oil and cooling liquid. Check up that all earlier removed wires and hoses are established on the places.
2. Disconnect an electric socket from the fuel pump.
3. Unscrew spark plugs and disconnect an electric socket from the ignition coil. Turn the engine a starter until the control lamp of pressure of oil will not go out, then screw in spark plugs and connect electric sockets to the coil of ignition and the fuel pump.
4. Start the engine. Engine start can be more long, than usually because of switching-off of fuel system.
5. At engine work idling check up absence of leaks of the fuel, cooling liquid and oil. At this stage of work of the engine the smell and a smoke from нагретых engine parts can be observed at burning out of the oil which have got on the engine at assemblage.
6. The engine should idle until the cooling liquid will not heat up that will be felt through the top hose of a radiator. Then switch off the engine. After engine cooling check up level of oil and cooling liquid.
7. At installation in the engine of new pistons, piston rings or bearings of a cranked shaft it is necessary to make обкатку the engine during run of the first 800 km.
8. Do not maintain the engine with completely open throttle заслонкой or under the big loading at low frequency of rotation of the engine. It is recommended to replace oil and the oil filter in the end of the period обкатки.