Subaru Legacy

Since 1990-1998 of release

Repair and car operation



Subaru Legasi
+ 1.1. Identification numbers
+ 2. Maintenance service
- 3. Engines
   3.1. Technical characteristics
   3.2. Operations on repair of the engine established in the car
   3.3. The top dead point of the first cylinder
   3.4. A cover of a head of the block of cylinders
   3.5. An inlet collector
   + 3.6. A gear belt and pulleys
   3.7. Replacement of a forward sealing ring of a cranked shaft
   3.8. Replacement of sealing rings of camshafts
   3.9. Camshafts and pushers
   3.10. Heads of the block of cylinders
   3.11. The oil pallet
   3.12. The oil pump
   3.13. The Flywheel / a drive plate
   3.14. Replacement of a back sealing ring of a cranked shaft
   3.15. A suspension bracket of the power unit
   - 3.16. Engine major repairs
      3.16.1. Technical characteristics
      3.16.2. Compression check
      3.16.3. Check of the engine by means of the vacuum gauge
      3.16.4. Recommendations about engine removal
      3.16.5. Engine removal
      3.16.6. Sequence of dismantling of the engine
      3.16.7. Dismantling of a head of the block of cylinders
      3.16.8. Clearing and survey of a head of the block of cylinders
      3.16.9. Assemblage of a head of the block of cylinders
      3.16.10. Removal of pistons
      3.16.11. Division of sections of blocks of cylinders
      3.16.12. Removal of a cranked shaft from rods
      3.16.13. The block of cylinders of the engine
      3.16.14. Хонингование cylinders
      3.16.15. Rods
      3.16.16. A cranked shaft
      3.16.17. Survey radical and шатунных bearings
      3.16.18. Engine balance of assembly at major repairs
      3.16.19. Survey of pistons
      3.16.20. Check of working backlashes шатунных bearings
      3.16.21. Check of working backlashes of radical bearings of a cranked shaft
      3.16.22. Assemblage of sections of the block of cylinders
      3.16.23. Installation of piston rings
      3.16.24. Installation of pistons
      3.16.25. Engine installation
      3.16.26. Start of the engine after major repairs
+ 4. Heating, ventilation
+ 5. Fuel system
+ 6. An exhaust system
+ 7. Systems of start, ignition
+ 8. Transmissions
+ 9. Coupling, shaft
+ 10. Brake system
+ 11. A suspension bracket
+ 12. A steering
+ 13. A body
+ 14. An electric equipment


3.16.25. Engine installation
PERFORMANCE ORDER
1. Apply a thin film high-temperature greasing on шлицы a conducted shaft of a transmission.
2. Using the load-lifting mechanism, lower the engine in a motor compartment. At engine installation if necessary incline and turn it so that it was established into place, without having caused harm.
3. Combine a cranked shaft of the engine with conducted shaft of a transmission. Move up the engine to a transmission and establish top, and then the bottom bolts of fastening of a transmission to the engine.
4. Lower a jack supporting a transmission and remove it from under the car.
5. Definitively lower the engine and remove from the engine slings of the load-lifting mechanism.
6. Raise the car so that it was possible to work under a motor compartment.
7. Fix engine support, having tightened bolts and nuts the demanded moment.
8. On models with an automatic transmission fix the hydrotransformer to a drive plate.
9. Establish a reception exhaust pipe.
10. Establish a coupling cable on the lever of deenergizing of coupling and adjust a cable.
11. The further installation is made in sequence, return to removal.
12. Adjust a tension приводных belts.
13. Fill in in the engine and a transmission oil.
14. Fill in cooling liquid in cooling system.