Subaru Legacy

Since 1990-1998 of release

Repair and car operation



Subaru Legasi
+ 1.1. Identification numbers
+ 2. Maintenance service
- 3. Engines
   3.1. Technical characteristics
   3.2. Operations on repair of the engine established in the car
   3.3. The top dead point of the first cylinder
   3.4. A cover of a head of the block of cylinders
   3.5. An inlet collector
   + 3.6. A gear belt and pulleys
   3.7. Replacement of a forward sealing ring of a cranked shaft
   3.8. Replacement of sealing rings of camshafts
   3.9. Camshafts and pushers
   3.10. Heads of the block of cylinders
   3.11. The oil pallet
   3.12. The oil pump
   3.13. The Flywheel / a drive plate
   3.14. Replacement of a back sealing ring of a cranked shaft
   3.15. A suspension bracket of the power unit
   - 3.16. Engine major repairs
      3.16.1. Technical characteristics
      3.16.2. Compression check
      3.16.3. Check of the engine by means of the vacuum gauge
      3.16.4. Recommendations about engine removal
      3.16.5. Engine removal
      3.16.6. Sequence of dismantling of the engine
      3.16.7. Dismantling of a head of the block of cylinders
      3.16.8. Clearing and survey of a head of the block of cylinders
      3.16.9. Assemblage of a head of the block of cylinders
      3.16.10. Removal of pistons
      3.16.11. Division of sections of blocks of cylinders
      3.16.12. Removal of a cranked shaft from rods
      3.16.13. The block of cylinders of the engine
      3.16.14. Хонингование cylinders
      3.16.15. Rods
      3.16.16. A cranked shaft
      3.16.17. Survey radical and шатунных bearings
      3.16.18. Engine balance of assembly at major repairs
      3.16.19. Survey of pistons
      3.16.20. Check of working backlashes шатунных bearings
      3.16.21. Check of working backlashes of radical bearings of a cranked shaft
      3.16.22. Assemblage of sections of the block of cylinders
      3.16.23. Installation of piston rings
      3.16.24. Installation of pistons
      3.16.25. Engine installation
      3.16.26. Start of the engine after major repairs
+ 4. Heating, ventilation
+ 5. Fuel system
+ 6. An exhaust system
+ 7. Systems of start, ignition
+ 8. Transmissions
+ 9. Coupling, shaft
+ 10. Brake system
+ 11. A suspension bracket
+ 12. A steering
+ 13. A body
+ 14. An electric equipment


e2a7ff6d e2a7ff6d

3.16.22. Assemblage of sections of the block of cylinders
PERFORMANCE ORDER
1. Clear interfaced surfaces of sections of the block of cylinders.
2. Establish a sealing ring of round section and a basic ring in the left section of the block of cylinders.
3. Apply a thin film hermetic on interfaced surfaces of sections of the block of cylinders (in drawing on the right – places of drawing of hermetic).
4. Establish the right section of the block of cylinders on left and screw in bolts of fastening of the right section, having tightened their moment from 18 to 28 Nanometers.
5. Arrange the block of cylinders horizontally and screw in bolts of fastening of the left section of the block of cylinders.
6. Tighten bolts of fastening of the right section the demanded moment in three stages from the centre to periphery. Then tighten bolts of fastening of the left section the demanded moment in three stages from the centre to periphery.
7. Establish a back sealing ring of a cranked shaft.
8. Check up that the forward sealing ring of a cranked shaft is established in a casing of the oil pump.