Subaru Legacy

Since 1990-1998 of release

Repair and car operation



Subaru Legasi
+ 1.1. Identification numbers
+ 2. Maintenance service
- 3. Engines
   3.1. Technical characteristics
   3.2. Operations on repair of the engine established in the car
   3.3. The top dead point of the first cylinder
   3.4. A cover of a head of the block of cylinders
   3.5. An inlet collector
   + 3.6. A gear belt and pulleys
   3.7. Replacement of a forward sealing ring of a cranked shaft
   3.8. Replacement of sealing rings of camshafts
   3.9. Camshafts and pushers
   3.10. Heads of the block of cylinders
   3.11. The oil pallet
   3.12. The oil pump
   3.13. The Flywheel / a drive plate
   3.14. Replacement of a back sealing ring of a cranked shaft
   3.15. A suspension bracket of the power unit
   - 3.16. Engine major repairs
      3.16.1. Technical characteristics
      3.16.2. Compression check
      3.16.3. Check of the engine by means of the vacuum gauge
      3.16.4. Recommendations about engine removal
      3.16.5. Engine removal
      3.16.6. Sequence of dismantling of the engine
      3.16.7. Dismantling of a head of the block of cylinders
      3.16.8. Clearing and survey of a head of the block of cylinders
      3.16.9. Assemblage of a head of the block of cylinders
      3.16.10. Removal of pistons
      3.16.11. Division of sections of blocks of cylinders
      3.16.12. Removal of a cranked shaft from rods
      3.16.13. The block of cylinders of the engine
      3.16.14. Хонингование cylinders
      3.16.15. Rods
      3.16.16. A cranked shaft
      3.16.17. Survey radical and шатунных bearings
      3.16.18. Engine balance of assembly at major repairs
      3.16.19. Survey of pistons
      3.16.20. Check of working backlashes шатунных bearings
      3.16.21. Check of working backlashes of radical bearings of a cranked shaft
      3.16.22. Assemblage of sections of the block of cylinders
      3.16.23. Installation of piston rings
      3.16.24. Installation of pistons
      3.16.25. Engine installation
      3.16.26. Start of the engine after major repairs
+ 4. Heating, ventilation
+ 5. Fuel system
+ 6. An exhaust system
+ 7. Systems of start, ignition
+ 8. Transmissions
+ 9. Coupling, shaft
+ 10. Brake system
+ 11. A suspension bracket
+ 12. A steering
+ 13. A body
+ 14. An electric equipment


e2a7ff6d Услуги лазерной резки металла подробнее.
купить диплом о высшем образовании с занесением в реестр Ставрополь.
e2a7ff6d Услуги лазерной резки металла подробнее.
купить диплом о высшем образовании с занесением в реестр Ставрополь.

3.16.14. Хонингование cylinders
THE GENERAL DATA

Хонингование walls of cylinders creates optimum conditions for work of piston rings.

The greatest distribution has received хонинговальный the tool with подпружиненными брусками.
Also it is widely applied хонинговальный the tool in the form of a round wire brush.

Besides, for carrying out хонингования a kerosene quantity, rags and electric сверлилка is required.
PERFORMANCE ORDER
1. Fix on electric сверлилке хонинговальный the tool and insert it into the cylinder,
2. Grease with a thin layer of kerosene of a wall of the cylinder, include electric сверлилку and move хонинговальный the tool upwards and down to that time while on walls correct crossed drawing is not formed.
3. Ideally lines should be crossed at an angle 60 .
4. Watch that in process хонингования walls have been moistened by a thin layer of kerosene.
5. Do not take хонинговальный the tool from the block of cylinders at included electric сверлилке. Moreover, make some courses хонинговального the tool at switched off сверлилке and only after that take it from the block of cylinders.
6. Similarly отхонингуйте other cylinders.
7. Carefully wash out the block of cylinders from the rests of the abrasive tool.
8. Dry up the block of cylinders and grease surfaces with a thin butter layer.