Subaru Legacy

Since 1990-1998 of release

Repair and car operation



Subaru Legasi
+ 1.1. Identification numbers
+ 2. Maintenance service
- 3. Engines
   3.1. Technical characteristics
   3.2. Operations on repair of the engine established in the car
   3.3. The top dead point of the first cylinder
   3.4. A cover of a head of the block of cylinders
   3.5. An inlet collector
   + 3.6. A gear belt and pulleys
   3.7. Replacement of a forward sealing ring of a cranked shaft
   3.8. Replacement of sealing rings of camshafts
   3.9. Camshafts and pushers
   3.10. Heads of the block of cylinders
   3.11. The oil pallet
   3.12. The oil pump
   3.13. The Flywheel / a drive plate
   3.14. Replacement of a back sealing ring of a cranked shaft
   3.15. A suspension bracket of the power unit
   - 3.16. Engine major repairs
      3.16.1. Technical characteristics
      3.16.2. Compression check
      3.16.3. Check of the engine by means of the vacuum gauge
      3.16.4. Recommendations about engine removal
      3.16.5. Engine removal
      3.16.6. Sequence of dismantling of the engine
      3.16.7. Dismantling of a head of the block of cylinders
      3.16.8. Clearing and survey of a head of the block of cylinders
      3.16.9. Assemblage of a head of the block of cylinders
      3.16.10. Removal of pistons
      3.16.11. Division of sections of blocks of cylinders
      3.16.12. Removal of a cranked shaft from rods
      3.16.13. The block of cylinders of the engine
      3.16.14. Хонингование cylinders
      3.16.15. Rods
      3.16.16. A cranked shaft
      3.16.17. Survey radical and шатунных bearings
      3.16.18. Engine balance of assembly at major repairs
      3.16.19. Survey of pistons
      3.16.20. Check of working backlashes шатунных bearings
      3.16.21. Check of working backlashes of radical bearings of a cranked shaft
      3.16.22. Assemblage of sections of the block of cylinders
      3.16.23. Installation of piston rings
      3.16.24. Installation of pistons
      3.16.25. Engine installation
      3.16.26. Start of the engine after major repairs
+ 4. Heating, ventilation
+ 5. Fuel system
+ 6. An exhaust system
+ 7. Systems of start, ignition
+ 8. Transmissions
+ 9. Coupling, shaft
+ 10. Brake system
+ 11. A suspension bracket
+ 12. A steering
+ 13. A body
+ 14. An electric equipment


e2a7ff6d e2a7ff6d

3.16.11. Division of sections of blocks of cylinders
THE GENERAL DATA

Details of sections of the block of cylinders

1 – long bolts

2 – blocks of cylinders

3 – a back sealing ring of a cranked shaft

4 – a cranked shaft and rods

5 – radical bearings of a cranked shaft

6 – the piston

PERFORMANCE ORDER
1. For division of sections of blocks of cylinders unscrew bolts of fastening of the left block of cylinders, and bolts of fastening of the right block of cylinders unscrew on two turns.
2. Establish the block of cylinders on a workbench the right party upwards. Unscrew bolts of fastening of the right block of cylinders.
3. Having pulled upwards, remove the right block of cylinders. Thus be careful, that rods have not fallen and have not damaged the block of cylinders. The cranked shaft and rods remain in the left block of cylinders.