Subaru Legacy

Since 1990-1998 of release

Repair and car operation



Subaru Legasi
+ 1.1. Identification numbers
+ 2. Maintenance service
- 3. Engines
   3.1. Technical characteristics
   3.2. Operations on repair of the engine established in the car
   3.3. The top dead point of the first cylinder
   3.4. A cover of a head of the block of cylinders
   3.5. An inlet collector
   + 3.6. A gear belt and pulleys
   3.7. Replacement of a forward sealing ring of a cranked shaft
   3.8. Replacement of sealing rings of camshafts
   3.9. Camshafts and pushers
   3.10. Heads of the block of cylinders
   3.11. The oil pallet
   3.12. The oil pump
   3.13. The Flywheel / a drive plate
   3.14. Replacement of a back sealing ring of a cranked shaft
   3.15. A suspension bracket of the power unit
   - 3.16. Engine major repairs
      3.16.1. Technical characteristics
      3.16.2. Compression check
      3.16.3. Check of the engine by means of the vacuum gauge
      3.16.4. Recommendations about engine removal
      3.16.5. Engine removal
      3.16.6. Sequence of dismantling of the engine
      3.16.7. Dismantling of a head of the block of cylinders
      3.16.8. Clearing and survey of a head of the block of cylinders
      3.16.9. Assemblage of a head of the block of cylinders
      3.16.10. Removal of pistons
      3.16.11. Division of sections of blocks of cylinders
      3.16.12. Removal of a cranked shaft from rods
      3.16.13. The block of cylinders of the engine
      3.16.14. Хонингование cylinders
      3.16.15. Rods
      3.16.16. A cranked shaft
      3.16.17. Survey radical and шатунных bearings
      3.16.18. Engine balance of assembly at major repairs
      3.16.19. Survey of pistons
      3.16.20. Check of working backlashes шатунных bearings
      3.16.21. Check of working backlashes of radical bearings of a cranked shaft
      3.16.22. Assemblage of sections of the block of cylinders
      3.16.23. Installation of piston rings
      3.16.24. Installation of pistons
      3.16.25. Engine installation
      3.16.26. Start of the engine after major repairs
+ 4. Heating, ventilation
+ 5. Fuel system
+ 6. An exhaust system
+ 7. Systems of start, ignition
+ 8. Transmissions
+ 9. Coupling, shaft
+ 10. Brake system
+ 11. A suspension bracket
+ 12. A steering
+ 13. A body
+ 14. An electric equipment


e2a7ff6d тыква рецепты в пост.
купить Золотую ладанку Золотой век.
Куплю отруби овсяные еще на сайте.
Испанские колбасы на сайте http://www.spanishfoods.com.ua.
e2a7ff6d тыква рецепты в пост.
купить Золотую ладанку Золотой век.
Куплю отруби овсяные еще на сайте.
Испанские колбасы на сайте http://www.spanishfoods.com.ua.

3.16.10. Removal of pistons
THE GENERAL DATA

Elements of fastening of piston fingers

1 – a stopper
2 – a lock ring
3 – a piston finger
4 – a flange
5 – short and long bolts of fastening of the left block of cylinders
6 – long bolts of fastening of the right block of cylinders

The prevention

If there is a deposit in the top part of the cylinder, remove its scraper from a soft material or the special adaptation


PERFORMANCE ORDER
1. For проворачивания a cranked shaft of the engine temporarily screw in a bolt of fastening of a pulley of a cranked shaft.
2. Unscrew stoppers from four technological apertures for access to lock rings of a piston finger.
3. For removal of a lock ring of a piston finger from the piston, establish the piston in the bottom dead point and, using flat-nose pliers, remove lock rings.
4. Using the special tool (or a hammer and the special tool), take piston fingers through technological apertures.
5. If necessary take the piston from the block of cylinders.