Subaru Legacy

Since 1990-1998 of release

Repair and car operation

Subaru Legasi
+ 1.1. Identification numbers
- 2. Maintenance service
   2.1. Introduction
   2.2. Technical characteristics
   2.3. Periodicity of service
   2.4. Check of level of engine oil
   2.5. Level of a cooling liquid
   2.6. Level of a brake liquid and a liquid of a drive of coupling
   2.7. A liquid for a windscreen washer
   2.8. Accumulator check
   2.9. Tyres and pressure check in tyres
   2.10. Check of level of oil in an automatic transmission
   2.11. Check of level of a liquid in the steering amplifier
   2.12. Replacement of oil and the oil filter
   2.13. Check and accumulator service
   2.14. Accumulator gymnastics
   2.15. Check of system of cooling
   2.16. Check of hoses, tubes and their replacement
   2.17. Check and replacement of brushes of screen wipers
   2.18. Shift of tyres
   2.19. Suspension bracket and steering check
   2.20. Exhaust system check
   2.21. Check of level of oil in a transmission and the main transfer
   2.22. Check of level of oil in differential (the main transfer)
   2.23. Check of brake system
   2.24. Check of the vacuum amplifier of brakes
   2.25. Check of a manual brake
   2.26. Check of fuel system
   2.27. Replacement of the fuel filter
   2.28. Check and replacement приводного a belt
   2.29. Check of a free wheeling of a pedal of a brake
   2.30. Check of a free wheeling of a pedal of coupling
   2.31. Check and replacement of spark plugs
   2.32. Check of high-voltage wires
   2.33. Check and adjustment of turns of idling
   2.34. Replacement of the air filter
   2.35. Check and replacement of the valve of ventilation картера (PCV)
   2.36. Check of system of catching of steams of fuel
   2.37. Check of system of repeated burning of the fulfilled gases (EGR)
   2.38. Service of system of cooling
   2.39. Replacement of a brake liquid
   2.40. Oil replacement in an automatic transmission
   2.41. Oil replacement in a mechanical transmission
   2.42. Check and adjustment of backlashes of valves
   + 2.43. The basic malfunctions
+ 3. Engines
+ 4. Heating, ventilation
+ 5. Fuel system
+ 6. An exhaust system
+ 7. Systems of start, ignition
+ 8. Transmissions
+ 9. Coupling, shaft
+ 10. Brake system
+ 11. A suspension bracket
+ 12. A steering
+ 13. A body
+ 14. An electric equipment


2.28. Check and replacement приводного a belt

Defects приводного a belt

Tension check приводного a belt

Privodnye belts are located from the forward party of the engine. Depending on a complete set of the car and the engine established in it, it is used one or the several приводных belts.


1. Uncover, closing belts, and check up a condition of belts on presence of cracks, stratifications and замасливания (fig. Defects приводного a belt see). If necessary replace a belt.
2. Check up a tension приводного a belt by means of two rulers.
3. The tension приводного a belt is necessary for adjusting so that by pressing by a hand thumb a long branch of a belt the deflection made approximately 5–6 mm.


Arrangement of bolts of fastening of a casing приводного a belt.

Bolts of fastening of a casing are specified by arrows.

Arrangement of bolts for tension adjustment приводного a generator belt

Arrangement of bolts for tension adjustment приводного a conditioner belt

For tension adjustment приводного a belt ослабьте fixing and, rotating an adjusting bolt, adjust a tension приводного a belt.


1. Ослабьте a tension приводного a belt also remove it from pulleys.
2. Establish приводные belts on pulleys. Thus belts should settle down precisely on the centre of pulleys. Adjust a tension приводных belts.