+ 1.1. Identification numbers
+ 2. Maintenance service
+ 3. Engines
+ 4. Heating, ventilation
+ 5. Fuel system
+ 6. An exhaust system
+ 7. Systems of start, ignition
+ 8. Transmissions
+ 9. Coupling, shaft
+ 10. Brake system
+ 11. A suspension bracket
+ 12. A steering
+ 13. A body
- 14. An electric equipment
- 14.1. A body electric equipment
14.1.2. Electric chains
14.1.3. Detection of not closed chain
14.1.4. Safety locks
14.1.5. Chain breakers
14.1.6. The relay
14.1.7. The relay of turns and the emergency light alarm system
14.1.8. Multipurpose switches of a steering column
14.1.9. The ignition lock
+ 14.1.10. Replacement of switches of the panel of devices
14.1.11. A combination of devices
14.1.12. A radio receiver
14.1.14. The aerial
14.1.15. The aerial with the electric drive
14.1.16. Replacement of bulbs of headlights
14.1.17. Adjustment of light of headlights
14.1.18. A headlight
14.1.19. Replacement of bulbs накаливания
14.1.20. The screen wiper engine
14.1.21. A sound signal
14.1.22. Check of a heater of back glass
14.1.23. Стеклоподъемники with the electric drive
14.1.24. Rear-view mirrors with the electric drive
14.1.25. A safety air cushion
+ 14.2. Electroschemes
The general description
The usual electric chain consists of an electric element, switches, the relay, engines, safety locks, automatic switches, wires and sockets which connect an electric element to the accumulator and a body. For the help by search of sources of malfunction of system of an electric equipment, in the end of a management schemes of an electric equipment of the car are resulted.
Before to try to define a malfunction source, in the beginning study the corresponding scheme of an electric equipment for representation reception about the elements established in this chain. The circle of possible sources of malfunction can be narrowed if to check up functioning of other elements entering into the given chain. If some elements or chains выхолят out of operation simultaneously the problem, obviously, consists in a safety lock, the general for these chains or elements, or contact to a body.
Electric problems are usually caused by the simple reasons, such, as the weakened or rusted sockets, absence of contact to a body, the fused safety locks, the fused burnt through crosspiece or the faulty relay. Visually check up a condition of all safety locks, wires and sockets in the failed chain before to start check of other elements. Use schemes of an electric equipment for that definition what of trailer clips are necessary for checking up for detection of a source of malfunction.
The basic tools necessary for detection of a source of malfunction are the tester or the voltmeter (a bulb on 12 volt and the pair of wires with щупами on the ends, also can be used for carrying out of some checks); an ohmmeter; the battery and a set of wires with щупами, накидной a puncture, it is desirable with the automatic switch or a safety lock which is used for detour of checked wires or elements.
For detection of the reason of what unreliable work or from elements (usually because of bad connection or pollution of contacts, or), it is possible to inspect the damaged isolation by stirring of wires. It is necessary to shake a wire by a hand to check up, whether there is a malfunction at wire movement. Such метолом it is possible to narrow a circle of possible sources of malfunction to any wire.
Along with problems because of bad connection of the wires, two basic types of malfunctions can take place in electric equipment system – the opened chain or short circuit.
Problems with the opened chain appear as a result of breakage in an electric equipment chain that interrupts current course. The opened chain will cause switching-off of an element of an electric equipment.
Problems with short circuit are caused by short circuit of a site of a chain that leads to leak of a current from other chain, usually directly on a body. Short circuit is usually caused by rupture of isolation of wires that allows a wire to concern other wire or any earthed element, for example bodies. Short circuit usually leads перегоранию a corresponding safety lock.
Detection of rupture of a chain
For check of integrity of a chain, connect the device for check of schemes or negative щуп the voltmeter to the negative plug of the accumulator or the earthed element.
Connect the second щуп to connection in a checked chain, it is desirable for the nearest to the accumulator or a safety lock. Thus this site of a chain should be energised from the accumulator if only the connection socket to the accumulator does not spend a current or has not fused a safety lock (thus do not forget that some chains of an electric equipment join only at key turn in the ignition lock in certain position).
Include a chain, then connect щуп a tester to the connection nearest to the switch of a chain on the party of the checked element.
If pressure is present (about what the control bulb testifies or voltmeter indications), it means that a site appreciate between corresponding connection and the switch has no ruptures.
Continue chain check by the same image, and after detection – a site on which there is no pressure, it means that chain rupture has occurred between this point and a point of the previous check on which there was a pressure. The majority of problems of the opened chain are caused by the broken or weakened socket.
Detection of a source of short circuit
For detection of a source of short circuit, in the beginning disconnect elements of loading of a chain (elements of loading of a chain are elements which consume an electric current, such as bulbs, electric motors, heating elements etc.).
Remove a corresponding safety lock and connect щупы a tester or the voltmeter to safety lock plugs.
Include a food in chains, thus do not forget that some chains of an electric equipment join only at key turn in the ignition lock in certain position.
If pressure is present (about what the control bulb testifies or voltmeter indications), it means that in a chain there is a short circuit.
If at carrying out of check of pressure is not present, however the safety lock on the former fuses at connection of that loading of a chain, it testifies to failure of an element of loading.
Detection of bad grounding
The negative plug of the accumulator is connected to "weight" – to metal of a body, the engine or a transmission thus many elements of an electric equipment are connected in such a manner that the positive wire, thus a current approaches to them only comes back to the accumulator through body metal. It means that fastening of an element of an electric equipment and a body are a part of an electric chain. Thereof, the bad or rusted fastening can cause refusal of work of an element or lead to its unstable or bad work. In particular, bulbs can burn with dim light (especially if in a point of grounding of this bulb grounding of any else included element of an electric equipment is carried out), electric motors can slowly work, and also work of one chain can have an effect imperceptible at first sight on work of other chain. Do not forget that on many cars grounding wires between some elements, such as the engine / of transmission and a body, that is in those places, where пет direct contact between metal elements, because of soft rubber fastenings or a paint coat are used.
For check of reliability of grounding of an element, it is necessary to disconnect the accumulator and to connect one of щупов an ohmmeter to reliably earthed element. Connect another щуп to a wire пли to connection with a body which is necessary for checking up. Resistance shown by an ohmmeter should be equal to zero; if is not present, check up connection as follows.
If you assume absence of grounding, disassemble connection and clear – a site of a body and the wire plug (or a surface of grounding of an element) to pure metal. Carefully remove all traces of a dirt, then by means of a knife remove all paint so that reliable contact of two metal surfaces has turned out. At assemblage, reliably tighten socket fastening; at connection of the plug of a wire, establish a washer with the jagged edges between the plug and a surface of a body for maintenance of reliable connection. At connection, prevent corrosion occurrence in the future, having put a layer of vaseline or silicone greasing.